Hyderabad · Apartment planning

Fitting Out an Older Building: What You Find Behind the Walls

In a new flat the unknowns are small and the tolerances are known. In a twenty-year-old flat almost everything concealed is a question, and pricing it as though it were new is how a renovation becomes an argument.

8 min readApartment planningPublished 21 Nov 2026

AlcorOne Solutions is an execution-first interior contracting firm delivering turnkey residential and commercial fit-outs across South India. It is headquartered in Chennai, with offices in Hyderabad, Visakhapatnam and Rajamahendravaram.


The Difference Is Uncertainty, Not Age

An older flat is not inherently a worse project. Older buildings frequently have advantages a new tower does not: more generous proportions, better cross-ventilation, thicker walls, established trees and, often, a location nothing new is being built in.

What is different is uncertainty. In a new flat, what is behind a wall is documented, recent and built to a known standard. In a twenty-year-old flat it is undocumented, aged, and has been modified by one or more previous owners in ways nobody recorded.

That single difference drives everything below, including how the contract should be structured.

Villa interior in Hyderabad by AlcorOne Solutions — Book-matched veneer ceiling
Book-matched veneer ceiling at a villa in Hyderabad — from a completed AlcorOne interior project. See the project

Electrical: Usually the Decisive Item

The most consequential difference, and the one most often deferred for cost reasons.

Older installations were designed for a load pattern that no longer exists. A flat wired when a household ran a fridge, a television, a few lights and fans is now asked to carry multiple air-conditioners, a microwave, an oven, a dishwasher, a washing machine, a geyser and a dozen chargers. The wiring may be sound; the provision frequently is not.

What to have assessed:

  • The sanctioned load and the distribution board. Older boards commonly have too few circuits, so high-load appliances end up sharing, which is both a nuisance and a hazard.
  • Earthing. Older installations sometimes have inadequate or degraded earthing, which is a safety matter rather than a comfort one.
  • Protective devices. Residual current protection may be absent entirely in an older installation.
  • Cable condition and type. Insulation degrades over decades, particularly where it runs warm.
  • Undocumented modifications. Previous owners add points, and those additions are rarely recorded and not always competent.

The honest recommendation for most older flats undergoing a substantial renovation is full rewiring. It is not the exciting part of a budget and it is the item where deferral is least defensible, because the walls will never be this open again. Deferring the wiring to fund the joinery means the wiring effectively never gets done — nobody reopens a finished flat for it.

Plumbing

The second system with a finite life. Older supply lines, particularly metal ones, corrode internally — narrowing the bore, reducing flow and eventually leaking. Drainage lines accumulate deposits and can be cracked or misaligned where the building has settled.

A functioning tap tells you little, because internal corrosion reduces flow long before it produces a leak. If a bathroom or a kitchen is being stripped, replacing the concealed lines while they are exposed is almost always the right call — and the same logic applies as for wiring: this is the cheapest it will ever be.

Two further points specific to older flats. Waterproofing is likely at or beyond its life, so any wet area being stripped should be re-tanked rather than re-tiled over an unknown membrane. And the substrate may have been wetting quietly for years, which needs drying time before a new membrane traps the moisture underneath.

Floors and Walls Are Not Where You Expect

Older buildings have settled, been re-floored, and been modified. Expect and check for:

Floors out of level, sometimes noticeably across a room. This matters for tall joinery, which needs a level base, and for any run of units that must align. A wardrobe on a floor with a fall across it needs scribing at the base.

Walls out of plumb and rooms out of square. More pronounced than in new construction. Long fitted runs need filler strips designed in rather than improvised, and the discrepancy needs measuring before manufacture — the twenty millimetres that travels to installation day is larger and more common here.

Multiple floor layers. Older flats have often been re-floored over the original, which changes threshold heights, door clearances and what happens when you strip back. Stripping may also reveal an original surface worth keeping.

Wall construction that varies. Some walls will be solid masonry, some may be later partitions. Which is which affects what can be fixed to them and what can be removed — and the structural question must be settled before any wall is opened, because in an older building the drawings that would answer it may not exist.

Materials From Another Era

Worth raising plainly rather than avoiding.

Buildings of certain periods used materials no longer considered acceptable. The most commonly encountered is asbestos-containing material, historically used in roofing sheets, some ceiling boards, certain pipe insulation and some floor coverings. It is generally hazardous when disturbed and broken up — which is exactly what demolition does.

If your building is of an era where this is plausible and you encounter a material you cannot identify during strip-out, stop and have it identified rather than breaking it up. This is not a reason for alarm about older buildings generally; it is a reason not to let an unidentified sheet material be smashed and swept away.

Lead-based paint on older joinery is the other legacy material worth being careful with, particularly where sanding is involved.

Access and the Building Itself

Older buildings frequently have smaller service lifts, or no lift adequate for material, or no service lift at all. That constrains what can be delivered assembled and may mean carrying material up stairs, which is slower and more expensive, and it changes how joinery should be manufactured.

Building management also tends to be less formalised. There may be no written interior work policy, which sounds easier and often is not — rules get applied reactively after a complaint. The protective step is to write to the association yourself setting out scope, hours, contractor and debris plan, and obtain written acknowledgement before starting.

How the Contract Should Be Structured

This is the practical conclusion, and it is the single most useful thing to get right.

A fixed price for an older building, written before anything is opened, is a price for a flat nobody has seen. It will either carry a large contingency, in which case you are paying for risk that may not materialise, or it will not, in which case it becomes a variation dispute the moment strip-out reveals something.

The honest structure has three parts:

  1. A survey and investigation stage, paid for as a separate item, including opening up a few small areas to establish what is actually there — the electrical, the plumbing, the substrate under a wet area, the floor build-up.
  2. A firm price for everything known, which after a proper survey is most of the job.
  3. A defined decision point after strip-out, with the likely discoveries already priced both ways, so the call on the day is a choice rather than a negotiation conducted with the flat open.

A contractor who proposes this structure is being straightforward with you. One who offers a confident fixed price for a forty-year-old flat without opening anything has either priced a large contingency into it or intends to raise variations later.


Written by Pradeep Kumar Vasadi

Pradeep Kumar Vasadi is a co-founder and Principal at AlcorOne Solutions. He grew up in Rajamahendravaram and spent years on the factory floors of Chennai’s manufacturing setups — hard, hands-on work that lit his drive to build something of his own. He now leads project delivery, on-site supervision, and vendor coordination, holding AlcorOne’s fit-outs to shop-floor standards of precision across South India.

Sources & references.

Standards, regulatory registries, and manufacturer references that back the material grades, pricing framework, and compliance points in this guide:

Frequently asked questions.

Do we really need to rewire? The existing wiring works.

Working and adequate are different tests, and the relevant one is whether the installation suits current loads safely. Have it assessed by a qualified electrician for earthing, protective devices, circuit count and cable condition rather than judged by whether the lights come on. Where the assessment says the installation is sound and simply needs additional circuits, that is a reasonable middle path. Where it flags earthing or degraded cable, the decision is made for you — and the time to act is while the walls are open, because a finished flat will not be reopened for it.

How much contingency should we allow for an older flat?

More than for a new one, and the better protection is investigation rather than a larger number. A contingency covers the cost of a surprise; a proper survey with a few small opening-up investigations reduces how many surprises there are, which is worth more. Spend on establishing the condition of the electrical, the plumbing and the wet-area substrate before pricing, then hold a contingency against what genuinely cannot be known until strip-out.

We found an unidentified sheet material while stripping out. What should we do?

Stop work in that area and do not break it up, sand it or sweep up debris from it. Have it identified by someone qualified before anything further happens, because the hazard from legacy materials comes principally from disturbing them. This is a short delay and a small cost against a genuine health risk to the people doing the work and to your household. Once identified as harmless, work resumes normally; if not, it is handled and removed appropriately.

Is it cheaper to renovate an older flat or buy a new one and fit it out?

They are rarely comparable on fit-out cost alone, because the older flat usually carries systems work a new flat does not need — rewiring, replumbing, re-tanking wet areas, levelling floors — before any interior work begins. What that comparison leaves out is everything that made the older flat attractive: location, proportions, ventilation and a plot nothing new is being built on. The useful approach is to price the systems work honestly as a separate figure, so the decision is made with the real number rather than an optimistic one.

Older buildings reward renovation and punish assumption. The systems behind the walls have a finite life, the geometry is not what a drawing says, and the only way to price the work honestly is to look before committing.

AlcorOne surveys and opens up before pricing an older flat, and fixes a joint decision point after strip-out with the likely discoveries priced both ways.

AlcorOne Solutions · Hyderabad

Older flat? Survey before price.

A fixed price for an older building written before anything is opened is a price for a flat nobody has seen yet.

Planning a project in Hyderabad?

Get a callback + itemised BOQ

Leave your name and number — we'll call you back with a scope and a ballpark BOQ for your Hyderabad project. No obligation.

We use these details only to respond to your enquiry — never sold or shared for marketing. Your IP address is recorded with the submission. Privacy Policy